* Library of Linear Technology definitions * Copyright 1989, 1990 Linear Technology Corporation * Neither this library nor any part may be copied without the express * written consent of Linear Technology Corporation * $Revision: 1.5 $ * $Author: mk $ * $Date: 27 Apr 1992 16:24:58 $ *----------------------------------------------------------------------------- * * This library of macromodels is being supplied to users as an aid to circuit * designs. While it reflects reasonably close similarity to the actual device * in terms of performance, it is not suggested as a replacement for * breadboarding. Simulation should be used as a forerunner or a supplement to * traditional lab testing. * * Users should very carefully note the following factors regarding these * models: * * Model performance in general will reflect typical baseline specs for a * given device, and certain aspects of performance may not be modeled * fully. * * While reasonable care has been taken in their preparation, we cannot * be responsible for correct application on any and all computer * systems. * * Model users are hereby notified that these models are supplied * "as is", with no direct or implied responsibility on the part of LTC * for their operation within a customer circuit or system. Further, * Linear Technology Corporation reserves the right to change these * models without prior notice. * * In all cases, the current data sheet information for a given real * device is your final design guideline, and is the only actual * performance guarantee. For further technical information, refer to * individual device data sheets. * * Your feedback and suggestions on these (and future) models will be * appreciated! * * Linear Technology Corporation * 1630 McCarthy Blvd. * Milpitas, CA, 95035 * (408) 432-1900 *----------------------------------------------------------------------------- * Linear Technology LF155 op amp model * Written: 05-10-1990 18:16:50 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(low)=7.0E+00V/us, SR(high)=1.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF155/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 2.1221E+03 rd2 40 90 2.1221E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 2.8000E-04 gosit 7 12 90 80 1.4000E-04 * intermediate gcm 0 8 12 0 4.7124E-09 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 4.2768E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0124E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1403E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1403E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.7200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=3.9655E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=3.9655E-04 vto=-9.980000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF155A op amp model * Written: 05-10-1990 18:19:48 Type: PFET input, internal comp. * Typical specs: * Vos=1.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(low)=7.0E+00V/us, SR(high)=1.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF155A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 2.1221E+03 rd2 40 90 2.1221E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 2.8000E-04 gosit 7 12 90 80 1.4000E-04 * intermediate gcm 0 8 12 0 4.7124E-09 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 4.2768E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0124E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1403E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1403E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.7200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=3.9655E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=3.9655E-04 vto=-9.990000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF156 op amp model * Written: 05-10-1990 18:26:49 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF156/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.8609E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0690E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.5200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=9.2528E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=9.2528E-04 vto=-9.980000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF156A op amp model * Written: 05-10-1990 18:28:18 Type: PFET input, internal comp. * Typical specs: * Vos=1.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF156A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.8609E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0690E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.5200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=9.2528E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=9.2528E-04 vto=-9.990000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF355 op amp model * Written: 05-10-1990 18:12:34 Type: PFET input, internal comp. * Typical specs: * Vos=3.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(low)=6.0E+00V/us, SR(high)=1.2E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF355/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 2.1221E+03 rd2 40 90 2.1221E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 2.4000E-04 gosit 7 12 90 80 1.2000E-04 * intermediate gcm 0 8 12 0 4.7124E-09 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 4.2768E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.9963E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1360E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1360E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.7600E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=4.6264E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=4.6264E-04 vto=-9.970000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF355A op amp model * Written: 05-10-1990 18:14:53 Type: PFET input, internal comp. * Typical specs: * Vos=1.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(low)=7.0E+00V/us, SR(high)=1.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF355A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 2.1221E+03 rd2 40 90 2.1221E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 2.8000E-04 gosit 7 12 90 80 1.4000E-04 * intermediate gcm 0 8 12 0 4.7124E-09 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 4.2768E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0124E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1403E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1403E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.7200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=3.9655E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=3.9655E-04 vto=-9.990000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF356 op amp model * Written: 05-10-1990 18:23:43 Type: PFET input, internal comp. * Typical specs: * Vos=3.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF356/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.8609E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0690E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.5200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=9.2528E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=9.2528E-04 vto=-9.970000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF356A op amp model * Written: 05-10-1990 18:25:11 Type: PFET input, internal comp. * Typical specs: * Vos=1.0E-03, Ib=3.0E-11, Ios=3.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=106.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF356A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.8609E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0690E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.5200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.1500E-11 beta=9.2528E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.8500E-11 beta=9.2528E-04 vto=-9.990000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF412 op amp model * Written: 05-10-1990 18:34:44 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=2.0E-11, Ios=1.5E-11, GBP=5.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=108.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF412/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.6458E+02 rd2 40 90 9.6458E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 1.0367E-08 ga 8 0 80 90 1.0367E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.4474E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0774E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.3800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.7500E-11 beta=1.0335E-03 vto=-1.000000E+00) .model jm2 pjf (is=1.2500E-11 beta=1.0335E-03 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LF412A op amp model * Written: 05-10-1990 18:37:21 Type: PFET input, internal comp. * Typical specs: * Vos=3.0E-04, Ib=1.5E-11, Ios=1.0E-11, GBP=5.7E+06Hz, Phase mar.= 45 deg, * SR(low)=1.5E+01V/us, SR(high)=3.0E+01V/us, Av=110.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LF412A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.3073E+02 rd2 40 90 9.3073E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 6.0000E-04 gosit 7 12 90 80 3.0000E-04 * intermediate gcm 0 8 12 0 1.0744E-08 ga 8 0 80 90 1.0744E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.9730E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0925E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1615E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1615E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.2000E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.0000E-11 beta=9.6199E-04 vto=-1.000000E+00) .model jm2 pjf (is=1.0000E-11 beta=9.6199E-04 vto=-9.997000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt LH2108/LT 3 2 7 4 6 1 8 x_LH2108/LT 3 2 7 4 6 1 8 LM108/LT .ends *----------------------------------------------------------------------------- .subckt LH2108A/LT 3 2 7 4 6 1 8 x_LH2108A/LT 3 2 7 4 6 1 8 LM108A/LT .ends *----------------------------------------------------------------------------- * Linear Technology LM101A op amp model * Written: 08-23-1989 15:55:44 Type: Bipolar npn input, external comp. * Typical specs: * Vos=7.0E-04, Ib=3.0E-08, Ios=1.5E-09, GBP=9.0E+05Hz, Phase mar.= 70 deg, * SR(+)=5.0E-01V/us, SR(-)=4.8E-01V/us, Av= 104 dB, CMMR= 96 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-30.0mA, Iq= 1800uA * * Connections: + - V+V-O CaCb .subckt LM101A/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 5.895E+03 rc2 7 90 5.895E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 c1 80 90 5.460E-12 re1 10 12 2.438E+03 re2 11 12 2.438E+03 iee 12 4 1.506E-05 re 12 0 1.328E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.689E-09 ga 8 0 80 90 1.696E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 1.401E+02 * output ro1 1 6 3.333E+01 ro2 1 0 6.667E+01 rc 17 0 4.758E-05 gc 0 17 6 0 2.102E+04 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.808E+00 ve 14 4 1.808E+00 ip 7 4 1.785E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=2.439E+02) .model qm2 npn (is=8.220E-16 bf=2.564E+02) .model dm1 d (is=3.337E-15) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LM107 op amp model * Written: 08-23-1989 15:53:34 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=7.0E-04, Ib=3.0E-08, Ios=1.5E-09, GBP=9.0E+05Hz, Phase mar.= 70 deg, * SR(+)=5.0E-01V/us, SR(-)=4.8E-01V/us, Av= 104 dB, CMMR= 96 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-30.0mA, Iq= 1800uA * * Connections: + - V+V-O .subckt LM107/LT 3 2 7 4 6 * input rc1 7 80 5.895E+03 rc2 7 90 5.895E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 c1 80 90 5.460E-12 re1 10 12 2.438E+03 re2 11 12 2.438E+03 iee 12 4 1.506E-05 re 12 0 1.328E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.689E-09 ga 8 0 80 90 1.696E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.401E+02 * output ro1 1 6 3.333E+01 ro2 1 0 6.667E+01 rc 17 0 4.758E-05 gc 0 17 6 0 2.102E+04 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.808E+00 ve 14 4 1.808E+00 ip 7 4 1.785E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=2.439E+02) .model qm2 npn (is=8.220E-16 bf=2.564E+02) .model dm1 d (is=3.337E-15) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LM108 op amp model (with calls for LH2108) * Written: 08-23-1989 15:42:36 Type: Bipolar npn input, external comp. * Typical specs: * Vos=7.0E-04, Ib=5.0E-10, Ios=5.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 110 dB, CMMR= 100 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/- 6.0mA, Iq= 300uA * (input differential mode clamp active) * * Connections: + - V+V-O CaCb .subckt LM108/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.001E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 1.131E-09 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 3.146E+01 * output ro1 1 6 1.111E+02 ro2 1 0 8.889E+02 rc 17 0 3.533E-04 gc 0 17 6 0 2.830E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.766E+00 ve 14 4 1.766E+00 ip 7 4 2.940E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=5.714E+03) .model qm2 npn (is=8.220E-16 bf=6.316E+03) .model dm1 d (is=1.192E-10) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LM108A op amp model (with calls for LH2108A) * Written: 08-23-1989 15:40:03 Type: Bipolar npn input, external comp. * Typical specs: * Vos=3.0E-04, Ib=5.0E-10, Ios=5.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 110 dB, CMMR= 110 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/- 6.0mA, Iq= 300uA * (input differential mode clamp active) * * Connections: + - V+V-O CaCb .subckt LM108A/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.001E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 3.576E-10 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 3.146E+01 * output ro1 1 6 1.111E+02 ro2 1 0 8.889E+02 rc 17 0 3.533E-04 gc 0 17 6 0 2.830E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.766E+00 ve 14 4 1.766E+00 ip 7 4 2.940E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=5.714E+03) .model qm2 npn (is=8.093E-16 bf=6.316E+03) .model dm1 d (is=1.192E-10) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LM118 op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LM118 data sheet, LTC 1990 databook p2-313 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LM118/LT 3 2 7 4 6 * input rc1 7 80 7.074E+02 rc2 7 90 7.074E+02 q1 80 2 10 qm1 q2 90 3 11 qm1 * c1 80 91 300e-12 rxc1 91 90 1e3 cxc1 91 90 15e-12 c2 1 8 5.000E-12 * rb1 2 102 1.0000E+00 rb2 3 103 1.0000E+00 ddm1 102 104 dm2 vz1 104 103 5.5 ddm2 103 105 dm2 vz2 105 102 5.5 re1 10 12 6.209E+02 re2 11 12 6.209E+02 iee 12 4 6.000E-04 re 12 0 3.332E+05 ce 12 0 2.632E-13 * gcm 0 8 12 0 1.414E-08 ga 8 0 80 90 1.414E-03 r2 8 0 1.000E+05 gb 1 0 8 0 5.318E+01 ro2 1 0 7.4000E+01 * rs 1 6 1 ecl 18 0 1 6 3.172e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.6473 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.6473 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 4.400E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=2.4390E+03) .model qm2 npn (is=8.6435E-16 bf=2.5641E+03) * .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LT118A op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LT118A data sheet, LTC 1990 databook p2-313 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LT118A/LT 3 2 7 4 6 * input rc1 7 80 7.074E+02 rc2 7 90 7.074E+02 q1 80 2 10 qm1 q2 90 3 11 qm1 * c1 80 91 300e-12 rxc1 91 90 1e3 cxc1 91 90 15e-12 c2 1 8 5.000E-12 * rb1 2 102 1.0000E+00 rb2 3 103 1.0000E+00 ddm1 102 104 dm2 vz1 104 103 5.5 ddm2 103 105 dm2 vz2 105 102 5.5 re1 10 12 6.209E+02 re2 11 12 6.209E+02 iee 12 4 6.000E-04 re 12 0 3.332E+05 ce 12 0 2.632E-13 * gcm 0 8 12 0 1.414E-08 ga 8 0 80 90 1.414E-03 r2 8 0 1.000E+05 gb 1 0 8 0 5.318E+01 ro2 1 0 7.4000E+01 * rs 1 6 1 ecl 18 0 1 6 3.172e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.6473 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.6473 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 4.400E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=2.4390E+03) .model qm2 npn (is=8.1562E-16 bf=2.5641E+03) * .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LM308 op amp model * Written: 08-23-1989 15:46:51 Type: Bipolar npn input, external comp. * Typical specs: * Vos=2.0E-03, Ib=1.5E-09, Ios=2.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 110 dB, CMMR= 100 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/- 6.0mA, Iq= 300uA * (input differential mode clamp active) * * Connections: + - V+V-O CaCb .subckt LM308/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.245E+02 re2 11 12 2.245E+02 iee 12 4 6.003E-06 re 12 0 3.332E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 1.131E-09 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 3.146E+01 * output ro1 1 6 1.111E+02 ro2 1 0 8.889E+02 rc 17 0 3.533E-04 gc 0 17 6 0 2.830E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.766E+00 ve 14 4 1.766E+00 ip 7 4 2.940E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=1.875E+03) .model qm2 npn (is=8.643E-16 bf=2.143E+03) .model dm1 d (is=1.192E-10) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LM308A op amp model * Written: 08-23-1989 15:45:03 Type: Bipolar npn input, external comp. * Typical specs: * Vos=3.0E-04, Ib=1.5E-09, Ios=2.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 110 dB, CMMR= 110 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/- 6.0mA, Iq= 300uA * (input differential mode clamp active) * * Connections: + - V+V-O CaCb .subckt LM308A/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.245E+02 re2 11 12 2.245E+02 iee 12 4 6.003E-06 re 12 0 3.332E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 3.576E-10 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 3.146E+01 * output ro1 1 6 1.111E+02 ro2 1 0 8.889E+02 rc 17 0 3.533E-04 gc 0 17 6 0 2.830E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.766E+00 ve 14 4 1.766E+00 ip 7 4 2.940E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=1.875E+03) .model qm2 npn (is=8.093E-16 bf=2.143E+03) .model dm1 d (is=1.192E-10) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LT1001 op amp model (with calls for LT1002) * Written: 10-16-1989 15:04:20 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=1.80E-05, Ib=7.00E-10, Ios=4.00E-10, GBP=8.0E+05Hz, Phase mar.=60.0deg, * SR(+)=3.3E-01V/us, SR(-)=3.1E-01V/us, Av=118dB, CMMR=126dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-25.0mA, Iq=1600uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt LT1001/LT 3 2 7 4 6 * input rc1 7 80 6.631E+03 rc2 7 90 6.631E+03 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 5.000E+02 rb2 3 103 5.000E+02 ddm1 102 104 dm2 ddm3 104 103 dm2 ddm2 103 105 dm2 ddm4 105 102 dm2 c1 80 90 8.660E-12 re1 10 12 1.409E+03 re2 11 12 1.409E+03 iee 12 4 9.901E-06 re 12 0 2.020E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 7.558E-11 ga 8 0 80 90 1.508E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.538E+03 * output ro1 1 6 2.575E+01 ro2 1 0 3.425E+01 rc 17 0 4.228E-06 gc 0 17 6 0 2.365E+05 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.803E+00 ve 14 4 1.803E+00 ip 7 4 1.590E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=5.500E+03) .model qm2 npn (is=8.006E-16 bf=9.900E+03) .model dm1 d (is=2.331E-08) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LT1001A op amp model (with calls for LT1002A) * Written: 10-16-1989 15:04:20 Type: Bipolar npn input, internal comp. * LT1001A updated from original model on 05-18-1990 * Typical specs: * Vos=1.00E-05, Ib=5.00E-10, Ios=3.00E-10, GBP=8.0E+05Hz, Phase mar.=60.0deg, * SR(+)=3.3E-01V/us, SR(-)=3.1E-01V/us, Av=118dB, CMMR=126dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-25.0mA, Iq=1600uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt LT1001A/LT 3 2 7 4 6 * input rc1 7 80 6.631E+03 rc2 7 90 6.631E+03 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 5.000E+02 rb2 3 103 5.000E+02 ddm1 102 104 dm2 ddm3 104 103 dm2 ddm2 103 105 dm2 ddm4 105 102 dm2 c1 80 90 8.660E-12 re1 10 12 1.409E+03 re2 11 12 1.409E+03 iee 12 4 9.901E-06 re 12 0 2.020E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 7.558E-11 ga 8 0 80 90 1.508E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.538E+03 * output ro1 1 6 2.575E+01 ro2 1 0 3.425E+01 rc 17 0 4.228E-06 gc 0 17 6 0 2.365E+05 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.803E+00 ve 14 4 1.803E+00 ip 7 4 1.590E-03 dsub 4 7 dm2 * models .model qm1 npn (Is=8.000E-16 Bf=7.692E+03) .model qm2 npn (Is=8.003E-16 Bf=1.429E+04) .model dm1 d (is=2.331E-08) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- .subckt LT1002/LT 3 2 7 4 6 x_LT1002/LT 3 2 7 4 6 LT1001/LT .ends *----------------------------------------------------------------------------- .subckt LT1002A/LT 3 2 7 4 6 x_LT1002A/LT 3 2 7 4 6 LT1001A/LT .ends *----------------------------------------------------------------------------- .subckt LT1006/LT 1 2 3 4 5 x_LT1006/LT 1 2 3 4 5 LT1013/LT .ends *----------------------------------------------------------------------------- * Linear Technology LT1006A op amp model * LT1006A updated from original model on 05-18-1990 * * Connections: + - V+V-O .subckt LT1006A/LT 1 2 3 4 5 * c1 11 12 8.661E-12 c2 6 7 30.00E-12 dc 8 53 dx de 54 8 dx dlp 90 91 dx dln 92 90 dx dp 4 3 dx egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5 fb 7 99 poly(5) vb vc ve vlp vln 0 2.475E9 -2E9 2E9 2E9 -2E9 ga 6 0 11 12 113.1E-6 gcm 0 6 10 99 225.7E-12 iee 3 10 dc 12.03E-6 hlim 90 0 vlim 1K q1 11 102 13 qm1 q2 12 101 14 qm2 rb1 2 102 400 rb2 1 101 400 dcm1 105 102 dx dcm2 105 101 dx vcmc 105 4 dc 0.4 r2 6 9 100.0E3 rc1 4 11 8.841E3 rc2 4 12 8.841E3 re1 13 10 4.519E3 re2 14 10 4.519E3 ree 10 99 16.63E6 ro1 8 5 80 ro2 7 99 25 ip 3 4 328E-6 vb 9 0 dc 0 vc 3 53 dc 1.610 ve 54 4 dc .61 vlim 7 8 dc 0 vlp 91 0 dc 25 vln 0 92 dc 25 .model dx D(Is=800.0E-18) .model qm1 pnp (Is=8.000E-16 Bf=6.623E+02) .model qm2 pnp (Is=8.006E-16 Bf=6.711E+02) .ends *----------------------------------------------------------------------------- * Linear Technology LT1007 op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LT1007 data sheet, LTC 1990 databook p2-57 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LT1007/LT 3 2 7 4 6 rc1 7 80 6.6315E+02 rc2 7 90 6.6315E+02 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 200e-12 rxc1 91 90 50 cxc1 91 90 500e-12 c2 8 98 4.000e-12 rxc2 8 98 4.00k cxc2 1 98 27.000e-12 * cin 3 2 5e-12 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -2.6233E+01 re2 11 12 -2.6233E+01 iee 12 4 7.5030E-05 re 12 0 2.666E+06 ce 12 0 1.579E-12 gcm 0 8 12 0 7.558E-10 ga 8 0 80 90 1.5080E-03 r2 8 0 1.000E+05 gb 1 0 8 0 1.9176E+03 ro2 1 0 6.900E+01 * rs 1 6 1 ecl 18 0 1 6 2.828e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.0909 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.0909 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 2.625E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=1.7857E+03) .model qm2 npn (is=8.0062E-16 bf=4.1667E+03) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LT1008 op amp model * Written: 08-18-1989 17:38:46 Type: Bipolar npn input, external comp. * Typical specs: * Vos=3.0E-05, Ib=3.0E-11, Ios=3.0E-11, GBP=6.0E+05Hz, Phase mar.= 60 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/- 8.0mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O CaCb .subckt LT1008/LT 3 2 7 4 6 1 8 ; Use C=30 pF in main circuit (Ca to Cb). * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 8.660E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.000E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.841E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 * external comp cap used for c2 (see note above). gb 1 0 8 0 1.960E+02 * output ro1 1 6 1.000E+02 ro2 1 0 9.000E+02 rc 17 0 6.802E-05 gc 0 17 6 0 1.470E+04 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.774E+00 ve 14 4 1.774E+00 ip 7 4 3.740E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=6.667E+04) .model qm2 npn (is=8.009E-16 bf=2.000E+05) .model dm1 d (is=4.276E-12) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LT1012 op amp model (with calls for LT1024) * Written: 09-05-1989 16:53:38 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=1.0E-05, Ib=3.0E-11, Ios=2.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt LT1012/LT 3 2 7 4 6 * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.000E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.841E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.960E+02 * output ro1 1 6 1.000E+02 ro2 1 0 9.000E+02 rc 17 0 1.063E-04 gc 0 17 6 0 9.408E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.785E+00 ve 14 4 1.785E+00 ip 7 4 3.740E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=7.500E+04) .model qm2 npn (is=8.003E-16 bf=1.500E+05) .model dm1 d (is=1.179E-19) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * This more complete macromodel has been adapted from the Parts * generated LT1013/LT1014 model. This version features closer * fidelity to the real part, with input common-mode clamping, and * compensated output clamping. It can be used for large signal * and/or single supply applications, where the inputs can * potentially be overdriven. Since it uses more active devices, * it may run more slowly than will a conventional macromodel. * * connections: non-inverting input * | inverting input * | | positive power supply * | | | negative power supply * | | | | output * | | | | | .subckt LT1013/LT 1 2 3 4 5 * c1 11 12 8.661E-12 c2 6 7 30.00E-12 dc 8 53 dx de 54 8 dx dlp 90 91 dx dln 92 90 dx dp 4 3 dx egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5 fb 7 99 poly(5) vb vc ve vlp vln 0 2.475E9 -2E9 2E9 2E9 -2E9 ga 6 0 11 12 113.1E-6 gcm 0 6 10 99 225.7E-12 iee 3 10 dc 12.03E-6 hlim 90 0 vlim 1K q1 11 102 13 qx q2 12 101 14 qx rb1 2 102 400 rb2 1 101 400 dcm1 105 102 dx dcm2 105 101 dx vcmc 105 4 dc 0.4 r2 6 9 100.0E3 rc1 4 11 8.841E3 rc2 4 12 8.841E3 re1 13 10 4.519E3 re2 14 10 4.519E3 ree 10 99 16.63E6 ro1 8 5 80 ro2 7 99 25 ip 3 4 328E-6 vb 9 0 dc 0 vc 3 53 dc 1.610 ve 54 4 dc .61 vlim 7 8 dc 0 vlp 91 0 dc 25 vln 0 92 dc 25 .model dx D(Is=800.0E-18) .model qx PNP(Is=800.0E-18 Bf=400) .ends *----------------------------------------------------------------------------- * Linear Technology LT1013A op amp model (with calls for LT1014A) * LT1013A updated from original model on 05-18-1990 * * Connections: + - V+V-O .subckt LT1013A/LT 1 2 3 4 5 * c1 11 12 8.661E-12 c2 6 7 30.00E-12 dc 8 53 dx de 54 8 dx dlp 90 91 dx dln 92 90 dx dp 4 3 dx egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5 fb 7 99 poly(5) vb vc ve vlp vln 0 2.475E9 -2E9 2E9 2E9 -2E9 ga 6 0 11 12 113.1E-6 gcm 0 6 10 99 225.7E-12 iee 3 10 dc 12.03E-6 hlim 90 0 vlim 1K q1 11 102 13 qm1 q2 12 101 14 qm2 rb1 2 102 400 rb2 1 101 400 dcm1 105 102 dx dcm2 105 101 dx vcmc 105 4 dc 0.4 r2 6 9 100.0E3 rc1 4 11 8.841E3 rc2 4 12 8.841E3 re1 13 10 4.519E3 re2 14 10 4.519E3 ree 10 99 16.63E6 ro1 8 5 80 ro2 7 99 25 ip 3 4 328E-6 vb 9 0 dc 0 vc 3 53 dc 1.610 ve 54 4 dc .61 vlim 7 8 dc 0 vlp 91 0 dc 25 vln 0 92 dc 25 .model dx D(Is=800.0E-18) .model qm1 pnp (Is=8.000E-16 Bf=4.969E+02) .model qm2 pnp (Is=8.012E-16 Bf=5.031E+02) .ends *----------------------------------------------------------------------------- .subckt LT1014/LT 1 2 3 4 5 x_LT1014/LT 1 2 3 4 5 LT1013/LT .ends *----------------------------------------------------------------------------- .subckt LT1014A/LT 1 2 3 4 5 x_LT1014A/LT 1 2 3 4 5 LT1013A/LT .ends *----------------------------------------------------------------------------- * Linear Technology LT1022 op amp model * Written: 05-10-1990 15:08:03 Type: PFET input, internal comp. * Typical specs: * Vos=1.0E-04, Ib=1.0E-11, Ios=2.0E-12, GBP=8.0E+06Hz, Phase mar.= 45 deg, * SR(low)=2.5E+01V/us, SR(high)=5.0E+01V/us, Av=112.0dB, CMRR= 92.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1022/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 6.6315E+02 rd2 40 90 6.6315E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 1.0000E-03 gosit 7 12 90 80 5.0000E-04 * intermediate gcm 0 8 12 0 3.7878E-08 ga 8 0 80 90 1.5080E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 5.3878E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7891E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9759E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9759E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.2000E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=1.1370E-03 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=1.1370E-03 vto=-9.999000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1022A op amp model * Written: 05-10-1990 15:06:43 Type: PFET input, internal comp. * Typical specs: * Vos=8.0E-05, Ib=1.0E-11, Ios=2.0E-12, GBP=8.0E+06Hz, Phase mar.= 45 deg, * SR(low)=2.5E+01V/us, SR(high)=5.0E+01V/us, Av=112.0dB, CMRR= 94.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1022A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 6.6315E+02 rd2 40 90 6.6315E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 1.0000E-03 gosit 7 12 90 80 5.0000E-04 * intermediate gcm 0 8 12 0 3.0088E-08 ga 8 0 80 90 1.5080E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 5.3878E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7891E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9759E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9759E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.2000E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=1.1370E-03 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=1.1370E-03 vto=-9.999200E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt LT1024/LT 3 2 7 4 6 x_LT1024/LT 3 2 7 4 6 LT1012/LT .ends *----------------------------------------------------------------------------- * Linear Technology LT1028 op amp model * Written: 11-28-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LT1028 data sheet, LTC 1990 databook p2-161 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LT1028/LT 3 2 7 4 6 rc1 7 80 7.0736E+01 rc2 7 90 7.0736E+01 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 750e-12 rxc1 91 90 50 cxc1 91 90 400e-12 c2 1 98 30.000E-12 rxc2 98 8 1k cxc2 98 8 10.000E-12 * cin 2 3 15e-12 rin 2 3 2e4 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -4.4157E+01 re2 11 12 -4.4157E+01 iee 12 4 4.5006E-04 re 12 0 4.4439E+05 ce 12 0 1.5789E-12 gcm 0 8 12 0 7.0854E-09 ga 8 0 80 90 1.4137E-02 r2 8 0 1.0000E+05 gb 1 0 8 0 2.6731E+02 ro2 1 0 7.9000E+01 * rs 1 6 1 ecl 18 0 1 6 2.7910e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.6394 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.6394 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 7.450E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=5.7692E+03) .model qm2 npn (is=8.0062E-16 bf=1.0714E+04) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LT1037 op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LT1037 data sheet, LTC 1990 databook p2-57 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LT1037/LT 3 2 7 4 6 rc1 7 80 6.6315E+02 rc2 7 90 6.6315E+02 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 200e-12 rxc1 91 90 200 cxc1 91 90 200e-12 c2 8 98 1.000e-12 rxc2 8 98 10.00k cxc2 1 98 5.000e-12 * cin 3 2 5e-12 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -2.6233E+01 re2 11 12 -2.6233E+01 iee 12 4 7.5030E-05 re 12 0 2.666E+06 ce 12 0 1.579E-12 gcm 0 8 12 0 7.558E-10 ga 8 0 80 90 1.5080E-03 r2 8 0 1.000E+05 gb 1 0 8 0 1.9176E+03 ro2 1 0 6.900E+01 * rs 1 6 1 ecl 18 0 1 6 2.828e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.0909 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.0909 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 2.625E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=1.7857E+03) .model qm2 npn (is=8.0062E-16 bf=4.1667E+03) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LT1055 op amp model * Written: 05-10-1990 16:19:03 Type: PFET input, internal comp. * Typical specs: * Vos=1.2E-04, Ib=1.0E-11, Ios=2.0E-12, GBP=4.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=112.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1055/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.1789E+03 rd2 40 90 1.1789E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 1.0679E-08 ga 8 0 80 90 8.4823E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 9.5783E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7241E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.3200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=7.4947E-04 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=7.4947E-04 vto=-9.998800E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1055A op amp model * Written: 05-10-1990 16:21:30 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-05, Ib=1.0E-11, Ios=2.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=112.0dB, CMRR=100.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1055A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 8.6205E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7312E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.2800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=8.5410E-04 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=8.5410E-04 vto=-9.999500E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1055S8 op amp model * Written: 05-10-1990 16:24:02 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=3.0E-11, Ios=5.0E-12, GBP=4.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.2E+01V/us, SR(high)=2.4E+01V/us, Av=112.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1055S8/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.1789E+03 rd2 40 90 1.1789E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.8000E-04 gosit 7 12 90 80 2.4000E-04 * intermediate gcm 0 8 12 0 1.0679E-08 ga 8 0 80 90 8.4823E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 9.5783E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7241E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9552E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9552E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.3200E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.2500E-11 beta=7.4947E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.7500E-11 beta=7.4947E-04 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1056 op amp model * Written: 05-10-1990 16:35:45 Type: PFET input, internal comp. * Typical specs: * Vos=1.4E-04, Ib=1.0E-11, Ios=2.0E-12, GBP=5.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.4E+01V/us, SR(high)=2.8E+01V/us, Av=112.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1056/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.6458E+02 rd2 40 90 9.6458E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.6000E-04 gosit 7 12 90 80 2.8000E-04 * intermediate gcm 0 8 12 0 1.3052E-08 ga 8 0 80 90 1.0367E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 7.8368E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7377E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9595E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9595E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.4400E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=9.5964E-04 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=9.5964E-04 vto=-9.998600E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1056A op amp model * Written: 05-10-1990 16:37:17 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-05, Ib=1.0E-11, Ios=2.0E-12, GBP=6.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.6E+01V/us, SR(high)=3.2E+01V/us, Av=112.0dB, CMRR=100.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1056A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 8.1618E+02 rd2 40 90 8.1618E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 6.4000E-04 gosit 7 12 90 80 3.2000E-04 * intermediate gcm 0 8 12 0 1.2252E-08 ga 8 0 80 90 1.2252E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 6.6312E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7495E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9633E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9633E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.3600E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.1000E-11 beta=1.1728E-03 vto=-1.000000E+00) .model jm2 pjf (is=9.0000E-12 beta=1.1728E-03 vto=-9.999500E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1056S8 op amp model * Written: 05-10-1990 17:54:40 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=3.0E-11, Ios=5.0E-12, GBP=5.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.4E+01V/us, SR(high)=2.8E+01V/us, Av=112.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-30mA, Rout= 50ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1056S8/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.6458E+02 rd2 40 90 9.6458E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.6000E-04 gosit 7 12 90 80 2.8000E-04 * intermediate gcm 0 8 12 0 1.3052E-08 ga 8 0 80 90 1.0367E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 7.8368E+01 ro2 1 0 4.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7377E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9595E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9595E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.4400E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=3.2500E-11 beta=9.5964E-04 vto=-1.000000E+00) .model jm2 pjf (is=2.7500E-11 beta=9.5964E-04 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1057 op amp model (with calls for LT1058) * Written: 05-10-1990 17:58:23 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-04, Ib=7.0E-12, Ios=4.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=110.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1057/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 1.1865E-08 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 3.3892E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0774E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.1800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=9.0000E-12 beta=8.5410E-04 vto=-1.000000E+00) .model jm2 pjf (is=5.0000E-12 beta=8.5410E-04 vto=-9.998000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1057A op amp model (with calls for LT1058A) * Written: 05-10-1990 18:03:20 Type: PFET input, internal comp. * Typical specs: * Vos=1.5E-04, Ib=5.0E-12, Ios=3.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.4E+01V/us, SR(high)=2.8E+01V/us, Av=111.0dB, CMRR=100.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1057A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.6000E-04 gosit 7 12 90 80 2.8000E-04 * intermediate gcm 0 8 12 0 9.4248E-09 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 3.8027E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0852E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9595E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9595E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.0400E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=6.5000E-12 beta=7.9309E-04 vto=-1.000000E+00) .model jm2 pjf (is=3.5000E-12 beta=7.9309E-04 vto=-9.998500E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology LT1057S op amp model * Written: 05-10-1990 18:05:04 Type: PFET input, internal comp. * Typical specs: * Vos=3.0E-04, Ib=1.0E-11, Ios=5.0E-12, GBP=5.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=110.0dB, CMRR= 98.0dB, * Vsat(+)=1.8V, Vsat(-)=1.8V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt LT1057S/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 1.0610E+03 rd2 40 90 1.0610E+03 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 1.1865E-08 ga 8 0 80 90 9.4248E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 3.3892E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0774E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 2.9575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 2.9575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.1800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=1.2500E-11 beta=8.5410E-04 vto=-1.000000E+00) .model jm2 pjf (is=7.5000E-12 beta=8.5410E-04 vto=-9.997000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.8000E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt LT1058/LT 3 2 7 4 6 x_LT1058/LT 3 2 7 4 6 LT1057/LT .ends *----------------------------------------------------------------------------- .subckt LT1058A/LT 3 2 7 4 6 x_LT1058A/LT 3 2 7 4 6 LT1057A/LT .ends *----------------------------------------------------------------------------- .subckt LT1077/LT 3 2 7 4 6 x_LT1077/LT 3 2 7 4 6 LT1078/LT .ends *----------------------------------------------------------------------------- * Linear Technology LT1078 op amp model (with calls for LT1079, LT1077) * Written: 10-17-1989 10:20:02 Type: Bipolar pnp input, internal comp. * Typical specs: * Vos=4.0E-05, Ib=6.0E-09, Ios=5.0E-11, GBP=2.0E+05Hz, Phase mar.= 60 deg, * SR(-)=8.0E-02V/us, SR(+)=7.6E-02V/us, Av= 120 dB, CMMR= 108 dB, * Vsat(+)=1.00V, Vsat(-)=0.00V, Isc=+/-15.0mA, Iq=45uA. * (input common mode clamp active) * (3 for 1!) * * Connections: + - V+V-O .subckt LT1078/LT 3 2 7 4 6 * input rc1 4 80 2.653E+04 rc2 4 90 2.653E+04 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 6.000E+02 rb2 3 103 6.000E+02 dcm1 105 102 dm2 dcm2 105 103 dm2 vcmc 105 4 4.000E-01 c1 80 90 8.660E-12 re1 10 12 4.958E+03 re2 11 12 4.958E+03 iee 7 12 2.412E-06 re 12 0 8.292E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 1.501E-10 ga 8 0 80 90 3.770E-05 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.396E+02 * output ro1 1 110 1.000E+02 ro2a 1 0 1.083E+03 ro2b 6 110 8.170E+02 ec 17 0 110 0 1 d1 1 17 dm1 d2 17 1 dm1 d3 110 13 dm2 d4 14 110 dm2 d5 6 110 dm2 d6 110 6 dm2 vc 7 13 1.790E+00 ve 14 4 7.901E-01 ip 7 4 4.259E-05 dsub 4 7 dm2 * models .model qm1 pnp (is=8.000E-16 bf=1.992E+02) .model qm2 pnp (is=8.012E-16 bf=2.008E+02) .model dm1 d (is=2.119E-24) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- .subckt LT1079/LT 3 2 7 4 6 x_LT1079/LT 3 2 7 4 6 LT1078/LT .ends *----------------------------------------------------------------------------- * Linear Technology LT1097 op amp model * Written: 12-05-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=1.0E-05, Ib=5.0e-11, Ios=2.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt LT1097/LT 3 2 7 4 6 * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.000E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.841E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.960E+02 * output ro1 1 6 1.000E+02 ro2 1 0 9.000E+02 rc 17 0 1.063E-04 gc 0 17 6 0 9.408E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.785E+00 ve 14 4 1.785E+00 ip 7 4 3.740E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=5.000e+04) .model qm2 npn (is=8.003E-16 bf=7.500e+05) .model dm1 d (is=1.179E-19) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology LT1101 instrumentation amplifier model * Written: 10-23-89 Type: Bipolar pnp input, single supply. * Typical specs: * Ref. LT1101 data sheet, LTC 1990 databook p13-36 * * Connections: Gnd G10a(-) V- V+ (+) G10b Out .subckt LT1101/LT 1 2 3 4 5 6 7 8 * r90a 1 2 828e3 r9a 2 100 82.8e3 ra 100 101 9.2e3 rb 101 102 9.2e3 r9b 102 7 82.8e3 r90b 7 8 828e3 * xa 3 100 5 4 101 LT1078 xb 6 102 5 4 8 LT1078 * rina 3 0 7e9 rinb 6 0 7e9 * .ends *----------------------------------------------------------------------------- * Linear Technology LT1115 op amp model * Written: 11-28-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. LT1115 data sheet, LTC Dec 1989 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt LT1115/LT 3 2 7 4 6 rc1 7 80 7.0736E+01 rc2 7 90 7.0736E+01 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 750e-12 rxc1 91 90 50 cxc1 91 90 400e-12 c2 1 98 30.000E-12 rxc2 98 8 1k cxc2 98 8 10.000E-12 * cin 2 3 15e-12 rin 2 3 2e4 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -4.4157E+01 re2 11 12 -4.4157E+01 iee 12 4 4.5006E-04 re 12 0 4.4439E+05 ce 12 0 1.5789E-12 gcm 0 8 12 0 7.0854E-09 ga 8 0 80 90 1.4137E-02 r2 8 0 1.0000E+05 gb 1 0 8 0 2.6731E+02 ro2 1 0 7.9000E+01 * rs 1 6 1 ecl 18 0 1 6 2.7910e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.6394 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.6394 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 7.450E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000e-16 bf=3.4615e+03) .model qm2 npn (is=8.0155e-16 bf=6.4286e+03) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology LT1178 op amp model (with calls for LT1179) * Written: 11-02-1989 13:20:10 Type: Bipolar pnp input, internal comp. * Typical specs: * Vos=4.0E-05, Ib=3.0E-09, Ios=5.0E-11, GBP=6.0E+04Hz, Phase mar.= 60 deg, * SR(-)=2.5E-02V/us, SR(+)=2.4E-02V/us, Av= 117 dB, CMMR= 102 dB, * Vsat(+)=1.00V, Vsat(-)=0.00V, Isc=+/- 5.0mA, Iq=14uA. * (input common mode clamp active) * (2 for 1) * * Connections: + - V+V-O .subckt LT1178/LT 3 2 7 4 6 * input rc1 4 80 8.842E+04 rc2 4 90 8.842E+04 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 6.000E+02 rb2 3 103 6.000E+02 dcm1 105 102 dm2 dcm2 105 103 dm2 vcmc 105 4 4.000E-01 c1 80 90 8.660E-12 re1 10 12 1.933E+04 re2 11 12 1.933E+04 iee 7 12 7.560E-07 re 12 0 2.646E+08 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 8.984E-11 ga 8 0 80 90 1.131E-05 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.647E+02 * output ro1 1 110 2.000E+02 ro2a 1 0 2.166E+03 ro2b 6 110 1.634E+03 ec 17 0 110 0 1 d1 1 17 dm1 d2 17 1 dm1 d3 110 13 dm2 d4 14 110 dm2 d5 6 110 dm2 d6 110 6 dm2 vc 7 13 1.762E+00 ve 14 4 7.617E-01 ip 7 4 1.324E-05 dsub 4 7 dm2 * models .model qm1 pnp (is=8.000E-16 bf=1.240E+02) .model qm2 pnp (is=8.012E-16 bf=1.261E+02) .model dm1 d (is=1.961E-16) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- .subckt LT1179/LT 3 2 7 4 6 x_LT1179/LT 3 2 7 4 6 LT1178/LT .ends *----------------------------------------------------------------------------- * Linear Technology LTC1049 op amp model * Written: 05-11-1990 11:36:48 Type: PMOS input, internal comp. * Typical specs: * Vos=2.0E-06, Ib=3.0E-11, Ios=1.5E-11, GBP=8.0E+05Hz, Phase mar.= 45 deg, * SR(-)=8.0E-01V/us, SR(+)=8.0E-01V/us, Av=160.0dB, CMRR=130.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 3/-10mA, Rout= 200ohms, Iq=0.20mA. * Note: Maximum total supply voltage for LTC1049 is 18 volts. * * Connections: + - V+V-O .subckt LTC1049/LT 3 2 7 4 6 * input rd1 4 80 6.6315E+03 rd2 4 90 6.6315E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 2.4000E-05 * intermediate gcm 0 8 12 0 4.7686E-11 ga 8 0 80 90 1.5080E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 3.3324E+04 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.8534E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 0.0000E+00 d2 20 21 dm1 vod2 21 18 1.9974E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.3894E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.3894E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 1.7600E-04 dsub 4 7 dm2 * models .model pm1 pmos (kp=9.4748E-04 vto=-1.1000000E+00) .model pm2 pmos (kp=9.4748E-04 vto=-1.1000020E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=1.9800E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=3.7500E-11) .model dmg2 d (is=2.2500E-11) .ends *----------------------------------------------------------------------------- * Linear Technology LTC1050 op amp model * Written: 05-11-1990 11:15:45 Type: PMOS input, internal comp. * Typical specs: * Vos=5.0E-07, Ib=1.0E-11, Ios=2.0E-11, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(-)=4.0E+00V/us, SR(+)=2.8E+00V/us, Av=160.0dB, CMRR=130.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 5/-20mA, Rout= 200ohms, Iq=1.00mA. * Note: Maximum total supply voltage for LTC1050 is 18 volts. * (Not modeled: clock) * * Connections: + - V+V-O .subckt LTC1050/LT 3 2 7 4 6 * input rd1 4 80 2.1221E+03 rd2 4 90 2.1221E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 1.2000E-04 cs 12 0 1.2857E-11 * intermediate gcm 0 8 12 0 1.4902E-10 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.0664E+04 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7955E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 0.0000E+00 d2 20 21 dm1 vod2 21 18 2.6932E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.4332E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.4332E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 8.8000E-04 dsub 4 7 dm2 * models .model pm1 pmos (kp=1.8506E-03 vto=-1.1000000E+00) .model pm2 pmos (kp=1.8506E-03 vto=-1.1000005E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=1.9800E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=2.0010E-11) .model dmg2 d (is=9.9998E-15) .ends *----------------------------------------------------------------------------- * Linear Technology LTC1050A op amp model * Written: 05-11-1990 11:24:39 Type: PMOS input, internal comp. * Typical specs: * Vos=5.0E-07, Ib=1.0E-11, Ios=2.0E-11, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(-)=4.0E+00V/us, SR(+)=2.8E+00V/us, Av=160.0dB, CMRR=140.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 5/-20mA, Rout= 200ohms, Iq=1.00mA. * Note: Maximum total supply voltage for LTC1050A is 18 volts. * (Not modeled: clock) * * Connections: + - V+V-O .subckt LTC1050A/LT 3 2 7 4 6 * input rd1 4 80 2.1221E+03 rd2 4 90 2.1221E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 1.2000E-04 cs 12 0 1.2857E-11 * intermediate gcm 0 8 12 0 4.7124E-11 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.0664E+04 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7955E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 0.0000E+00 d2 20 21 dm1 vod2 21 18 2.6932E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.4332E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.4332E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 8.8000E-04 dsub 4 7 dm2 * models .model pm1 pmos (kp=1.8506E-03 vto=-1.1000000E+00) .model pm2 pmos (kp=1.8506E-03 vto=-1.1000005E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=1.9800E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=2.0010E-11) .model dmg2 d (is=9.9998E-15) .ends *----------------------------------------------------------------------------- * Linear Technology LTC1051 op amp model (with calls for LTC1053) * Written: 05-11-1990 15:56:09 Type: PMOS input, internal comp. * Typical specs: * Vos=5.0E-07, Ib=3.0E-11, Ios=1.5E-11, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(-)=4.0E+00V/us, SR(+)=2.8E+00V/us, Av=160.0dB, CMRR=130.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 5/-20mA, Rout= 200ohms, Iq=1.00mA. * Note: Maximum total supply voltage for LTC1051 is 18 volts. * * Connections: + - V+V-O .subckt LTC1051/LT 3 2 7 4 6 * input rd1 4 80 2.1221E+03 rd2 4 90 2.1221E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 1.2000E-04 cs 12 0 1.2857E-11 * intermediate gcm 0 8 12 0 1.4902E-10 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.0664E+04 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7955E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 0.0000E+00 d2 20 21 dm1 vod2 21 18 2.6932E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.4332E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.4332E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 8.8000E-04 dsub 4 7 dm2 * models .model pm1 pmos (kp=1.8506E-03 vto=-1.1000000E+00) .model pm2 pmos (kp=1.8506E-03 vto=-1.1000005E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=1.9800E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=3.7500E-11) .model dmg2 d (is=2.2500E-11) .ends *----------------------------------------------------------------------------- * Linear Technology LTC1052 op amp model (with calls for LTC1052CS, LTC7652) * Written: 05-11-1990 11:30:03 Type: PMOS input, internal comp. * Typical specs: * Vos=5.0E-07, Ib=3.0E-12, Ios=1.0E-12, GBP=1.2E+06Hz, Phase mar.= 45 deg, * SR(-)=4.0E+00V/us, SR(+)=3.2E+00V/us, Av=150.0dB, CMRR=140.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 5/-15mA, Rout= 200ohms, Iq=1.70mA. * Note: Maximum total supply voltage for LTC1052 is 18 volts. * (Not modeled: clock & Cext) * * Connections: + - V+V-O .subckt LTC1052/LT 3 2 7 4 6 * input rd1 4 80 4.4210E+03 rd2 4 90 4.4210E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 1.2000E-04 cs 12 0 7.5000E-12 * intermediate gcm 0 8 12 0 2.2619E-11 ga 8 0 80 90 2.2619E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 7.0253E+03 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 1.7955E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 0.0000E+00 d2 20 21 dm1 vod2 21 18 1.7955E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.4332E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.4332E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 1.5800E-03 dsub 4 7 dm2 * models .model pm1 pmos (kp=4.2637E-04 vto=-1.1000000E+00) .model pm2 pmos (kp=4.2637E-04 vto=-1.1000005E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=1.9800E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=3.5000E-12) .model dmg2 d (is=2.5000E-12) .ends *----------------------------------------------------------------------------- .subckt LTC1052CS/LT 3 2 7 4 6 x_LTC1052CS/LT 3 2 7 4 6 LTC1052/LT .ends *----------------------------------------------------------------------------- .subckt LTC1053/LT 3 2 7 4 6 x_LTC1053/LT 3 2 7 4 6 LTC1051/LT .ends *----------------------------------------------------------------------------- * Linear Technology LTC1150 op amp model * Written: 05-11-1990 11:42:22 Type: PMOS input, internal comp. * Typical specs: * Vos=5.0E-07, Ib=2.0E-11, Ios=1.0E-11, GBP=2.5E+06Hz, Phase mar.= 45 deg, * SR(-)=3.0E+00V/us, SR(+)=2.1E+00V/us, Av=180.0dB, CMRR=145.0dB, * Vsat(+)=0.010V, Vsat(-)=0.010V, Isc=+ 3/-12mA, Rout= 200ohms, Iq=0.80mA. * (Not modeled: clock & Isupply) * * Connections: + - V+V-O .subckt LTC1150/LT 3 2 7 4 6 * input rd1 4 80 2.1221E+03 rd2 4 90 2.1221E+03 m1 80 2 12 12 pm1 m2 90 3 12 12 pm2 cin 2 3 5.0000E-12 dg1 2 7 dmg1 dg2 3 7 dmg2 c1 80 90 1.5000E-11 iss 7 12 9.0000E-05 cs 12 0 1.2857E-11 * intermediate gcm 0 8 12 0 2.6500E-11 ga 8 0 80 90 4.7124E-04 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.0664E+05 ro2 1 0 1.9900E+02 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.9675E+02 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+01 d1 18 19 dm1 vod1 19 20 5.9605E-08 d2 20 21 dm1 vod2 21 18 2.6708E+00 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 1.4253E+00 rpla 7 70 1.0000E+01 rplb 7 131 1.0000E+03 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 1.4253E+00 rnla 60 4 1.0000E+01 rnlb 141 4 1.0000E+03 * ip 7 4 7.1000E-04 dsub 4 7 dm2 * models .model pm1 pmos (kp=2.4674E-03 vto=-1.1000000E+00) .model pm2 pmos (kp=2.4674E-03 vto=-1.1000005E+00) .model dm1 d (is=1.0000E-20) .model dm2 d (is=8.0000E-16 bv=3.9600E+01) .model dm3 d (is=1.0000E-16) .model dmg1 d (is=2.5000E-11) .model dmg2 d (is=1.5000E-11) .ends *----------------------------------------------------------------------------- .subckt LTC7652/LT 3 2 7 4 6 x_LTC7652/LT 3 2 7 4 6 LTC1052/LT .ends *----------------------------------------------------------------------------- * Linear Technology OP-05 op amp model * Written: 08-23-1989 15:59:46 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=2.0E-04, Ib=1.0E-09, Ios=1.0E-09, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=3.0E-01V/us, SR(-)=2.9E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq= 3000uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt OP-05/LT 3 2 7 4 6 * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 5.000E+02 rb2 3 103 5.000E+02 ddm1 102 104 dm2 ddm3 104 103 dm2 ddm2 103 105 dm2 ddm4 105 102 dm2 c1 80 90 5.460E-12 re1 10 12 3.097E+03 re2 11 12 3.097E+03 iee 12 4 9.002E-06 re 12 0 2.222E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 5.668E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 6.647E+02 * output ro1 1 6 3.333E+01 ro2 1 0 6.667E+01 rc 17 0 1.393E-05 gc 0 17 6 0 7.179E+04 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 2.803E+00 ve 14 4 2.803E+00 ip 7 4 2.991E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=3.000E+03) .model qm2 npn (is=8.062E-16 bf=9.000E+03) .model dm1 d (is=5.991E-12) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology OP-07 op amp model * Written: 08-24-1989 12:35:59 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=3.0E-05, Ib=1.0E-09, Ios=4.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.5E-01V/us, SR(-)=2.4E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq=2500uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt OP-07/LT 3 2 7 4 6 * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 102 10 qm1 q2 90 103 11 qm2 rb1 2 102 5.000E+02 rb2 3 103 5.000E+02 ddm1 102 104 dm2 ddm3 104 103 dm2 ddm2 103 105 dm2 ddm4 105 102 dm2 c1 80 90 5.460E-12 re1 10 12 1.948E+03 re2 11 12 1.948E+03 iee 12 4 7.502E-06 re 12 0 2.666E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 5.668E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.294E+03 * output ro1 1 6 2.575E+01 ro2 1 0 3.425E+01 rc 17 0 6.634E-06 gc 0 17 6 0 1.507E+05 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 2.803E+00 ve 14 4 2.803E+00 ip 7 4 2.492E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=3.125E+03) .model qm2 npn (is=8.009E-16 bf=4.688E+03) .model dm1 d (is=1.486E-08) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology OP-15A op amp model (with calls for OP-15E) * Written: 05-10-1990 18:51:28 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-04, Ib=1.8E-11, Ios=5.0E-12, GBP=6.0E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=108.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-15A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 8.8419E+02 rd2 40 90 8.8419E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 1.1310E-08 ga 8 0 80 90 1.1310E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.2434E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0774E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.1800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.0500E-11 beta=1.2299E-03 vto=-1.000000E+00) .model jm2 pjf (is=1.5500E-11 beta=1.2299E-03 vto=-9.998000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology OP-15B op amp model (with calls for OP-15F) * Written: 05-10-1990 18:54:03 Type: PFET input, internal comp. * Typical specs: * Vos=4.0E-04, Ib=4.0E-11, Ios=1.0E-11, GBP=5.7E+06Hz, Phase mar.= 45 deg, * SR(low)=1.1E+01V/us, SR(high)=2.2E+01V/us, Av=107.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-15B/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.3073E+02 rd2 40 90 9.3073E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 4.4000E-04 gosit 7 12 90 80 2.2000E-04 * intermediate gcm 0 8 12 0 1.0744E-08 ga 8 0 80 90 1.0744E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.1047E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0598E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1528E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1528E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.2600E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=4.5000E-11 beta=1.3118E-03 vto=-1.000000E+00) .model jm2 pjf (is=3.5000E-11 beta=1.3118E-03 vto=-9.996000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology OP-15C op amp model (with calls for OP-15G) * Written: 05-10-1990 18:49:01 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=8.0E-11, Ios=2.0E-11, GBP=5.4E+06Hz, Phase mar.= 45 deg, * SR(low)=9.0E+00V/us, SR(high)=1.8E+01V/us, Av=106.0dB, CMRR= 96.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 3mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-15C/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.8244E+02 rd2 40 90 9.8244E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 3.6000E-04 gosit 7 12 90 80 1.8000E-04 * intermediate gcm 0 8 12 0 1.6132E-08 ga 8 0 80 90 1.0179E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.9800E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0387E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1472E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1472E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 2.4400E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=9.0000E-11 beta=1.4390E-03 vto=-1.000000E+00) .model jm2 pjf (is=7.0000E-11 beta=1.4390E-03 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt OP-15E/LT 3 2 7 4 6 x_OP-15E/LT 3 2 7 4 6 OP-15A/LT .ends *----------------------------------------------------------------------------- .subckt OP-15F/LT 3 2 7 4 6 x_OP-15F/LT 3 2 7 4 6 OP-15B/LT .ends *----------------------------------------------------------------------------- .subckt OP-15G/LT 3 2 7 4 6 x_OP-15G/LT 3 2 7 4 6 OP-15C/LT .ends *----------------------------------------------------------------------------- * Linear Technology OP-16A op amp model (with calls for OP-16E) * Written: 05-10-1990 19:00:18 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-04, Ib=2.0E-11, Ios=5.0E-12, GBP=8.0E+06Hz, Phase mar.= 45 deg, * SR(low)=2.0E+01V/us, SR(high)=4.0E+01V/us, Av=108.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-16A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 6.6315E+02 rd2 40 90 6.6315E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 8.0000E-04 gosit 7 12 90 80 4.0000E-04 * intermediate gcm 0 8 12 0 1.5080E-08 ga 8 0 80 90 1.5080E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.2510E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.1231E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1696E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1696E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 3.8000E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.2500E-11 beta=1.4212E-03 vto=-1.000000E+00) .model jm2 pjf (is=1.7500E-11 beta=1.4212E-03 vto=-9.998000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology OP-16B op amp model (with calls for OP-16F) * Written: 05-10-1990 19:02:39 Type: PFET input, internal comp. * Typical specs: * Vos=4.0E-04, Ib=4.0E-11, Ios=1.0E-11, GBP=7.6E+06Hz, Phase mar.= 45 deg, * SR(low)=1.8E+01V/us, SR(high)=3.6E+01V/us, Av=107.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-16B/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 6.9805E+02 rd2 40 90 6.9805E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 7.2000E-04 gosit 7 12 90 80 3.6000E-04 * intermediate gcm 0 8 12 0 1.4326E-08 ga 8 0 80 90 1.4326E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.1118E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.1119E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1666E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1666E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 3.8800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=4.5000E-11 beta=1.4252E-03 vto=-1.000000E+00) .model jm2 pjf (is=3.5000E-11 beta=1.4252E-03 vto=-9.996000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology OP-16C op amp model (with calls for OP-16G) * Written: 05-10-1990 18:57:16 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=8.0E-11, Ios=2.0E-11, GBP=7.2E+06Hz, Phase mar.= 45 deg, * SR(low)=1.6E+01V/us, SR(high)=3.2E+01V/us, Av=106.0dB, CMRR= 96.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 75ohms, Iq= 5mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-16C/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 7.3683E+02 rd2 40 90 7.3683E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 6.4000E-04 gosit 7 12 90 80 3.2000E-04 * intermediate gcm 0 8 12 0 2.1510E-08 ga 8 0 80 90 1.3572E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 1.9867E+01 ro2 1 0 7.4000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0994E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1633E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1633E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 4.1600E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=9.0000E-11 beta=1.4390E-03 vto=-1.000000E+00) .model jm2 pjf (is=7.0000E-11 beta=1.4390E-03 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt OP-16E/LT 3 2 7 4 6 x_OP-16E/LT 3 2 7 4 6 OP-16A/LT .ends *----------------------------------------------------------------------------- .subckt OP-16F/LT 3 2 7 4 6 x_OP-16F/LT 3 2 7 4 6 OP-16B/LT .ends *----------------------------------------------------------------------------- .subckt OP-16G/LT 3 2 7 4 6 x_OP-16G/LT 3 2 7 4 6 OP-16C/LT .ends *----------------------------------------------------------------------------- * Linear Technology OP-27 op amp model (with calls for OP-227) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. OP-27 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt OP-27/LT 3 2 7 4 6 rc1 7 80 6.6315E+02 rc2 7 90 6.6315E+02 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 200e-12 rxc1 91 90 50 cxc1 91 90 500e-12 c2 8 98 4.000e-12 rxc2 8 98 4.00k cxc2 1 98 27.000e-12 * cin 3 2 5e-12 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -2.6233E+01 re2 11 12 -2.6233E+01 iee 12 4 7.5030E-05 re 12 0 2.666E+06 ce 12 0 1.579E-12 gcm 0 8 12 0 7.558E-10 ga 8 0 80 90 1.5080E-03 r2 8 0 1.000E+05 gb 1 0 8 0 1.9176E+03 ro2 1 0 6.900E+01 * rs 1 6 1 ecl 18 0 1 6 2.828e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.0909 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.0909 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 2.625E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=2.0000E+03) .model qm2 npn (is=8.0093E-16 bf=4.6667E+03) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology OP-37 op amp model (with calls for OP-237) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * Typical specs: * Ref. OP-37 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .subckt OP-37/LT 3 2 7 4 6 rc1 7 80 6.6315E+02 rc2 7 90 6.6315E+02 q1 80 2 10 qm1 q2 90 3 11 qm2 * c1 80 91 200e-12 rxc1 91 90 200 cxc1 91 90 200e-12 c2 8 98 1.000e-12 rxc2 8 98 10.00k cxc2 1 98 5.000e-12 * cin 3 2 5e-12 ddm1 2 104 dm2 ddm3 104 3 dm2 ddm2 3 105 dm2 ddm4 105 2 dm2 re1 10 12 -2.6233E+01 re2 11 12 -2.6233E+01 iee 12 4 7.5030E-05 re 12 0 2.666E+06 ce 12 0 1.579E-12 gcm 0 8 12 0 7.558E-10 ga 8 0 80 90 1.5080E-03 r2 8 0 1.000E+05 gb 1 0 8 0 1.9176E+03 ro2 1 0 6.900E+01 * rs 1 6 1 ecl 18 0 1 6 2.828e+01 gcl 0 8 20 0 1 rcl 20 0 1e3 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1 vc 13 6 3.0909 rpla 7 70 1e4 rplb 7 131 1e5 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1 ve 6 14 3.0909 rnla 60 4 1e4 rnlb 141 4 1e5 * ip 7 4 2.625E-03 dsub 4 7 dm2 * models .model qm1 npn (is=8.0000E-16 bf=2.0000E+03) .model qm2 npn (is=8.0093E-16 bf=4.6667E+03) .model dm1 d (is=1.000e-19) .model dm2 d (is=8.000E-16) .model dm3 d (is=1.000e-20) .ends *----------------------------------------------------------------------------- * Linear Technology OP-97 op amp model * Written: 12-06-89 Type: Bipolar npn input, internal comp. * Typical specs: * Vos=3.0e-05, Ib=3.0E-11, Ios=2.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .subckt OP-97/LT 3 2 7 4 6 * input rc1 7 80 8.842E+03 rc2 7 90 8.842E+03 q1 80 2 10 qm1 q2 90 3 11 qm2 ddm1 2 3 dm2 ddm2 3 2 dm2 c1 80 90 5.460E-12 re1 10 12 2.246E+02 re2 11 12 2.246E+02 iee 12 4 6.000E-06 re 12 0 3.333E+07 ce 12 0 1.579E-12 * intermediate gcm 0 8 12 0 2.841E-11 ga 8 0 80 90 1.131E-04 r2 8 0 1.000E+05 c2 1 8 3.000E-11 gb 1 0 8 0 1.960E+02 * output ro1 1 6 1.000E+02 ro2 1 0 9.000E+02 rc 17 0 1.063E-04 gc 0 17 6 0 9.408E+03 d1 1 17 dm1 d2 17 1 dm1 d3 6 13 dm2 d4 14 6 dm2 vc 7 13 1.785E+00 ve 14 4 1.785E+00 ip 7 4 3.740E-04 dsub 4 7 dm2 * models .model qm1 npn (is=8.000E-16 bf=7.500E+04) .model qm2 npn (is=8.008e-16 bf=1.500E+05) .model dm1 d (is=1.179E-19) .model dm2 d (is=8.000E-16) .ends *----------------------------------------------------------------------------- * Linear Technology OP-215A op amp model (with calls for OP-215E) * Written: 05-10-1990 18:44:02 Type: PFET input, internal comp. * Typical specs: * Vos=2.0E-04, Ib=1.5E-11, Ios=1.0E-11, GBP=5.7E+06Hz, Phase mar.= 45 deg, * SR(low)=1.5E+01V/us, SR(high)=3.0E+01V/us, Av=112.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-215A/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.3073E+02 rd2 40 90 9.3073E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 6.0000E-04 gosit 7 12 90 80 3.0000E-04 * intermediate gcm 0 8 12 0 1.0744E-08 ga 8 0 80 90 1.0744E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 3.7427E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0925E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1615E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1615E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.3000E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.0000E-11 beta=9.6199E-04 vto=-1.000000E+00) .model jm2 pjf (is=1.0000E-11 beta=9.6199E-04 vto=-9.998000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=5.2800E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- * Linear Technology OP-215C op amp model (with calls for OP-215G) * Written: 05-10-1990 18:40:39 Type: PFET input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=2.0E-11, Ios=1.5E-11, GBP=5.5E+06Hz, Phase mar.= 45 deg, * SR(low)=1.3E+01V/us, SR(high)=2.6E+01V/us, Av=108.0dB, CMRR=100.0dB, * Vsat(+)=2.0V, Vsat(-)=2.0V, Isc=+/-25mA, Rout= 100ohms, Iq= 2mA. * (input cm clamp *optional*) * * Connections: + - V+V-O .subckt OP-215C/LT 3 2 7 4 6 * input vcm2 40 4 2.0000E+00 rd1 40 80 9.6458E+02 rd2 40 90 9.6458E+02 j1 80 102 12 jm1 j2 90 103 12 jm2 cin 2 3 4.0000E-12 rg1 2 102 2.0000E+00 rg2 3 103 2.0000E+00 ** cm clamp * dcm1 107 103 dm4 * dcm2 105 107 dm4 * vcmc 105 4 4.0E+00 * ecmp 106 4 103 4 1 * rcmp 107 106 1E+04 * dcm3 109 102 dm4 * dcm4 105 109 dm4 * ecmn 108 4 102 4 1 * rcmn 109 108 1E+04 ** end cm clamp c1 80 90 1.5000E-11 iss 7 12 5.2000E-04 gosit 7 12 90 80 2.6000E-04 * intermediate gcm 0 8 12 0 1.0367E-08 ga 8 0 80 90 1.0367E-03 r2 8 0 1.0000E+05 c2 1 8 3.0000E-11 gb 1 0 8 0 2.4474E+01 ro2 1 0 9.9000E+01 * output rso 1 6 1.0000E+00 ecl 18 0 1 6 2.0774E+01 gcl 0 8 20 0 1.0000E+00 rcl 20 0 1.0000E+03 d1 18 20 dm1 d2 20 18 dm1 * d3a 131 70 dm3 d3b 13 131 dm3 gpl 0 8 70 7 1.0000E+00 vc 13 6 3.1575E+00 rpla 7 70 1.0000E+04 rplb 7 131 1.0000E+05 d4a 60 141 dm3 d4b 141 14 dm3 gnl 0 8 60 4 1.0000E+00 ve 6 14 3.1575E+00 rnla 60 4 1.0000E+04 rnlb 141 4 1.0000E+05 * ip 7 4 1.3800E-03 dsub 4 7 dm2 * models .model jm1 pjf (is=2.7500E-11 beta=1.0335E-03 vto=-1.000000E+00) .model jm2 pjf (is=1.2500E-11 beta=1.0335E-03 vto=-9.995000E-01) .model dm1 d (is=1.0000E-15) .model dm2 d (is=8.0000E-16 bv=4.3200E+01) .model dm3 d (is=1.0000E-16) .model dm4 d (is=1.0000E-09) .ends *----------------------------------------------------------------------------- .subckt OP-215E/LT 3 2 7 4 6 x_OP-215E/LT 3 2 7 4 6 OP-215A/LT .ends *----------------------------------------------------------------------------- .subckt OP-215G/LT 3 2 7 4 6 x_OP-215G/LT 3 2 7 4 6 OP-215C/LT .ends *----------------------------------------------------------------------------- .subckt OP-227/LT 3 2 7 4 6 x_OP-227/LT 3 2 7 4 6 OP-27/LT .ends *----------------------------------------------------------------------------- .subckt OP-237/LT 3 2 7 4 6 x_OP-237/LT 3 2 7 4 6 OP-37/LT .ends * * Linear Technology LM301A op amp model * Written: 08-23-1989 15:55:44 Type: Bipolar npn input, external comp. * LM301A updated from original model on 05-21-1990 * Typical specs: * Vos=2.0E-03, Ib=7.0E-08, Ios=3.0E-09, GBP=9.0E+05Hz, Phase mar.= 70 deg, * SR(+)=5.0E-01V/us, SR(-)=4.8E-01V/us, Av= 104 dB, CMMR= 96 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-30.0mA, Iq= 1800uA * * Connections: + - V+V-O CaCb .SUBCKT LM301A/LT 3 2 7 4 6 1 8 * USE C=30 PF IN MAIN CIRCUIT (CA TO CB). * INPUT RC1 7 80 5.895E+03 RC2 7 90 5.895E+03 Q1 80 2 10 QM1 Q2 90 3 11 QM2 C1 80 90 5.460E-12 RE1 10 12 2.438E+03 RE2 11 12 2.438E+03 IEE 12 4 1.506E-05 RE 12 0 1.328E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 2.689E-09 GA 8 0 80 90 1.696E-04 R2 8 0 1.000E+05 * EXTERNAL COMP CAP USED FOR C2 (SEE NOTE ABOVE). GB 1 0 8 0 1.401E+02 * OUTPUT RO1 1 6 3.333E+01 RO2 1 0 6.667E+01 RC 17 0 4.758E-05 GC 0 17 6 0 2.102E+04 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 1.808E+00 VE 14 4 1.808E+00 IP 7 4 1.785E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=1.049E+02) .MODEL QM2 NPN (IS=8.647E-16 BF=1.095E+02) .MODEL DM1 D (IS=3.337E-15) .MODEL DM2 D (IS=8.000E-16) .ENDS LM301A/LT * * * Linear Technology LM307 op amp model * Written: 08-23-1989 15:53:34 Type: Bipolar npn input, internal comp. * LM307 updated from original model on 05-21-1990 * Typical specs: * Vos=2.0E-03, Ib=7.0E-08, Ios=3.0E-09, GBP=9.0E+05Hz, Phase mar.= 70 deg, * SR(+)=5.0E-01V/us, SR(-)=4.8E-01V/us, Av= 104 dB, CMMR= 96 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-30.0mA, Iq= 1800uA * * Connections: + - V+V-O .SUBCKT LM307/LT 3 2 7 4 6 * INPUT RC1 7 80 5.895E+03 RC2 7 90 5.895E+03 Q1 80 2 10 QM1 Q2 90 3 11 QM2 C1 80 90 5.460E-12 RE1 10 12 2.438E+03 RE2 11 12 2.438E+03 IEE 12 4 1.506E-05 RE 12 0 1.328E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 2.689E-09 GA 8 0 80 90 1.696E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.401E+02 * OUTPUT RO1 1 6 3.333E+01 RO2 1 0 6.667E+01 RC 17 0 4.758E-05 GC 0 17 6 0 2.102E+04 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 1.808E+00 VE 14 4 1.808E+00 IP 7 4 1.785E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=1.049E+02) .MODEL QM2 NPN (IS=8.647E-16 BF=1.095E+02) .MODEL DM1 D (IS=3.337E-15) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology LM318 op amp model (with calls for LM318S8) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * LM318 updated from original model on 05-22-1990 * Typical specs: * Ref. LM318 data sheet, LTC 1990 databook p2-311 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT LM318/LT 3 2 7 4 6 * INPUT RC1 7 80 7.074E+02 RC2 7 90 7.074E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM1 * C1 80 91 300E-12 RXC1 91 90 1E3 CXC1 91 90 15E-12 C2 1 8 5.000E-12 * RB1 2 102 1.0000E+00 RB2 3 103 1.0000E+00 DDM1 102 104 DM2 VZ1 104 103 5.5 DDM2 103 105 DM2 VZ2 105 102 5.5 RE1 10 12 6.209E+02 RE2 11 12 6.209E+02 IEE 12 4 6.000E-04 RE 12 0 3.332E+05 CE 12 0 2.632E-13 * GCM 0 8 12 0 1.414E-08 GA 8 0 80 90 1.414E-03 R2 8 0 1.000E+05 GB 1 0 8 0 5.318E+01 RO2 1 0 7.4000E+01 * RS 1 6 1 ECL 18 0 1 6 3.172E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.6473 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.6473 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 4.400E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=1.818E+03) .MODEL QM2 NPN (IS=9.347E-16 BF=2.222E+03) * .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * .SUBCKT LM318S8/LT 3 2 7 4 6 X_LM318S8 3 2 7 4 6 LM318/LT .ENDS * * * Linear Technology LT1006S8 op amp model * LT1006S8 updated from original model on 05-21-1990 * * Connections: + - V+V-O .SUBCKT LT1006S8/LT 1 2 3 4 5 * C1 11 12 8.661E-12 C2 6 7 30.00E-12 DC 8 53 DX DE 54 8 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY(2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY(5) VB VC VE VLP VLN 0 2.475E9 -2E9 2E9 2E9 -2E9 GA 6 0 11 12 113.1E-6 GCM 0 6 10 99 225.7E-12 IEE 3 10 DC 12.03E-6 HLIM 90 0 VLIM 1K Q1 11 102 13 QM1 Q2 12 101 14 QM2 RB1 2 102 400 RB2 1 101 400 DCM1 105 102 DX DCM2 105 101 DX VCMC 105 4 DC 0.4 R2 6 9 100.0E3 RC1 4 11 8.841E3 RC2 4 12 8.841E3 RE1 13 10 4.519E3 RE2 14 10 4.519E3 REE 10 99 16.63E6 RO1 8 5 80 RO2 7 99 25 IP 3 4 328E-6 VB 9 0 DC 0 VC 3 53 DC 1.610 VE 54 4 DC .61 VLIM 7 8 DC 0 VLP 91 0 DC 25 VLN 0 92 DC 25 .MODEL DX D(IS=800.0E-18) .MODEL QM1 PNP (IS=8.000E-16 BF=5.955E+02) .MODEL QM2 PNP (IS=8.025E-16 BF=6.045E+02) .ENDS * * Linear Technology LT1007A op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * LT1007A updated from original model on 05-21-1990 * Typical specs: * Ref. LT1007A data sheet, LTC 1990 databook p2-57 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT LT1007A/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 50 CXC1 91 90 500E-12 C2 8 98 4.000E-12 RXC2 8 98 4.00K CXC2 1 98 27.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.778E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=5.769E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS LT1007A/LT * * * Linear Technology LT1012A op amp model (with calls for LT1024A) * Written: 09-05-1989 16:53:38 Type: Bipolar npn input, internal comp. * LT1012A updated from original model on 06-20-1990 * Typical specs: * Vos=8.0E-06, Ib=2.5E-11, Ios=1.5E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1012A/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 2 10 QM1 Q2 90 3 11 QM2 DDM1 2 3 DM2 DDM2 3 2 DM2 C1 80 90 5.460E-12 RE1 10 12 2.246E+02 RE2 11 12 2.246E+02 IEE 12 4 6.000E-06 RE 12 0 3.333E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 2.841E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.960E+02 * OUTPUT RO1 1 6 1.000E+02 RO2 1 0 9.000E+02 RC 17 0 1.063E-04 GC 0 17 6 0 9.408E+03 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 1.785E+00 VE 14 4 1.785E+00 IP 7 4 3.740E-04 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=9.231E+04) .MODEL QM2 NPN (IS=8.002E-16 BF=1.714E+05) .MODEL DM1 D (IS=1.179E-19) .MODEL DM2 D (IS=8.000E-16) .ENDS * .SUBCKT LT1024A/LT 3 2 7 4 6 X_LT1024A 3 2 7 4 6 LT1012A/LT .ENDS * * * Linear Technology LT1012D op amp model * Written: 09-05-1989 16:53:38 Type: Bipolar npn input, internal comp. * LT1012D updated from original model on 06-20-1990 * Typical specs: * Vos=1.2E-05, Ib=3.0E-11, Ios=2.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1012D/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 2 10 QM1 Q2 90 3 11 QM2 DDM1 2 3 DM2 DDM2 3 2 DM2 C1 80 90 5.460E-12 RE1 10 12 2.246E+02 RE2 11 12 2.246E+02 IEE 12 4 6.000E-06 RE 12 0 3.333E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 2.841E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.960E+02 * OUTPUT RO1 1 6 1.000E+02 RO2 1 0 9.000E+02 RC 17 0 1.063E-04 GC 0 17 6 0 9.408E+03 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 1.785E+00 VE 14 4 1.785E+00 IP 7 4 3.740E-04 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=7.500E+04) .MODEL QM2 NPN (IS=8.004E-16 BF=1.500E+05) .MODEL DM1 D (IS=1.179E-19) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology LT1012S8 op amp model * Written: 09-05-1989 16:53:38 Type: Bipolar npn input, internal comp. * LT1012S8 updated from original model on 06-20-1990 * Typical specs: * Vos=1.5E-05, Ib=8.0E-11, Ios=5.0E-11, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.0E-01V/us, SR(-)=1.9E-01V/us, Av= 126 dB, CMMR= 132 dB, * Vsat(+)=1.00V, Vsat(-)=1.00V, Isc=+/-12.5mA, Iq= 380uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1012S8/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 2 10 QM1 Q2 90 3 11 QM2 DDM1 2 3 DM2 DDM2 3 2 DM2 C1 80 90 5.460E-12 RE1 10 12 2.246E+02 RE2 11 12 2.246E+02 IEE 12 4 6.000E-06 RE 12 0 3.333E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 2.841E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.960E+02 * OUTPUT RO1 1 6 1.000E+02 RO2 1 0 9.000E+02 RC 17 0 1.063E-04 GC 0 17 6 0 9.408E+03 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 1.785E+00 VE 14 4 1.785E+00 IP 7 4 3.740E-04 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.857E+04) .MODEL QM2 NPN (IS=8.005E-16 BF=5.455E+04) .MODEL DM1 D (IS=1.179E-19) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology LT1013D op amp model (with calls for LT1014D) * LT1013D updated from original model on 05-18-1990 * * Connections: + - V+V-O .SUBCKT LT1013D/LT 1 2 3 4 5 * C1 11 12 8.661E-12 C2 6 7 30.00E-12 DC 8 53 DX DE 54 8 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY(2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY(5) VB VC VE VLP VLN 0 2.475E9 -2E9 2E9 2E9 -2E9 GA 6 0 11 12 113.1E-6 GCM 0 6 10 99 225.7E-12 IEE 3 10 DC 12.03E-6 HLIM 90 0 VLIM 1K Q1 11 102 13 QM1 Q2 12 101 14 QM2 RB1 2 102 400 RB2 1 101 400 DCM1 105 102 DX DCM2 105 101 DX VCMC 105 4 DC 0.4 R2 6 9 100.0E3 RC1 4 11 8.841E3 RC2 4 12 8.841E3 RE1 13 10 4.519E3 RE2 14 10 4.519E3 REE 10 99 16.63E6 RO1 8 5 80 RO2 7 99 25 IP 3 4 328E-6 VB 9 0 DC 0 VC 3 53 DC 1.610 VE 54 4 DC .61 VLIM 7 8 DC 0 VLP 91 0 DC 25 VLN 0 92 DC 25 .MODEL DX D(IS=800.0E-18) .MODEL QM1 PNP (IS=8.000E-16 BF=3.974E+02) .MODEL QM2 PNP (IS=8.062E-16 BF=4.027E+02) .ENDS *--------------------------------------------------------------- * CONNECTIONS: + - V+V-O .SUBCKT LT1014D/LT 1 2 3 4 5 * X_LT1014D 1 2 3 4 5 LT1013D/LT .ENDS * * Linear Technology LT1028A op amp model * Written: 11-28-1989 Type: Bipolar npn input, internal comp. * LT1028A updated from original model on 05-22-1990 * Typical specs: * Ref. LT1028A data sheet, LTC 1990 databook p2-161 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT LT1028A/LT 3 2 7 4 6 RC1 7 80 7.0736E+01 RC2 7 90 7.0736E+01 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 750E-12 RXC1 91 90 50 CXC1 91 90 400E-12 C2 1 98 30.000E-12 RXC2 98 8 1K CXC2 98 8 10.000E-12 * CIN 2 3 15E-12 RIN 2 3 2E4 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -4.4157E+01 RE2 11 12 -4.4157E+01 IEE 12 4 4.5006E-04 RE 12 0 4.4439E+05 CE 12 0 1.5789E-12 GCM 0 8 12 0 7.0854E-09 GA 8 0 80 90 1.4137E-02 R2 8 0 1.0000E+05 GB 1 0 8 0 2.6731E+02 RO2 1 0 7.9000E+01 * RS 1 6 1 ECL 18 0 1 6 2.7910E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.6394 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.6394 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 7.450E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=7.258E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=1.184E+04) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * * * Linear Technology LT1037A op amp model * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * LT1037A updated from original model on 05-21-1990 * Typical specs: * Ref. LT1037A data sheet, LTC 1990 databook p2-57 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT LT1037A/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 200 CXC1 91 90 200E-12 C2 8 98 1.000E-12 RXC2 8 98 10.00K CXC2 1 98 5.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.778E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=5.769E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * * * Linear Technology LT1078A op amp model (with calls for LT1079A) * Written: 06-20-1990 13:27:10 Type: Bipolar pnp input, internal comp. * Typical specs: * Vos=3.0E-05, Ib=6.0E-09, Ios=5.0E-11, GBP=2.0E+05Hz, Phase mar.= 60 deg, * SR(-)=8.0E-02V/us, SR(+)=7.6E-02V/us, Av= 120 dB, CMMR= 108 dB, * Vsat(+)=0.70V, Vsat(-)=0.00V, Isc=+/-15.0mA, Iq= 45uA. * (input common mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1078A/LT 3 2 7 4 6 * INPUT RC1 4 80 2.653E+04 RC2 4 90 2.653E+04 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 6.000E+02 RB2 3 103 6.000E+02 DCM1 105 102 DM2 DCM2 105 103 DM2 VCMC 105 4 4.000E-01 C1 80 90 8.660E-12 RE1 10 12 4.958E+03 RE2 11 12 4.958E+03 IEE 7 12 2.412E-06 RE 12 0 8.292E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 1.501E-10 GA 8 0 80 90 3.770E-05 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 2.449E+02 * OUTPUT RO1 1 110 1.000E+02 RO2A 1 0 1.083E+03 RO2B 6 110 8.170E+02 EC 17 0 110 0 1 D1 1 17 DM1 D2 17 1 DM1 D3 110 13 DM2 D4 14 110 DM2 D5 6 110 DM2 D6 110 6 DM2 VC 7 13 1.490E+00 VE 14 4 7.911E-01 IP 7 4 4.259E-05 DSUB 4 7 DM2 * MODELS .MODEL QM1 PNP (IS=8.000E-16 BF=1.992E+02) .MODEL QM2 PNP (IS=8.009E-16 BF=2.008E+02) .MODEL DM1 D (IS=3.718E-24) .MODEL DM2 D (IS=8.000E-16) .ENDS * .SUBCKT LT1079A/LT 3 2 7 4 6 X_LT1079A 3 2 7 4 6 LT1078A/LT .ENDS * * * Linear Technology LT1122 op amp model * Written: 09-18-1990 10:15:55 Type: PFET input, internal comp. * Typical specs: * Vos=6.0E-04, Ib=2.7E-11, Ios=5.0E-12, GBP=1.5E+07Hz, Phase mar.= 57 deg, * SR(-)=7.5E+01V/us, SR(+)=7.5E+01V/us, Av=112.0dB, CMRR= 98.0dB, * Vsat(+)=2.5V, Vsat(-)=1.0V, Isc=+/-40mA, Rout= 40ohms, Iq= 7mA. * * Connections: + - V+V-O .SUBCKT LT1122/LT 3 2 7 4 6 * INPUT RD1 4 80 3.5368E+02 RD2 4 90 3.5368E+02 J1 80 2 12 JM1 J2 90 3 12 JM2 CIN 2 3 4.0000E-12 C1 80 90 9.7411E-12 ISS 7 12 2.2500E-03 * INTERMEDIATE GCM 0 8 12 0 3.5595E-08 GA 8 0 80 90 2.8274E-03 R2 8 0 1.0000E+05 C2 1 8 3.0000E-11 GB 1 0 8 0 3.6103E+01 RO2 1 0 3.9000E+01 * OUTPUT RSO 1 6 1.0000E+00 ECL 18 0 1 6 1.3974E+01 GCL 0 8 20 0 1.0000E+00 RCL 20 0 1.0000E+03 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1.0000E+00 VC 13 6 3.6997E+00 RPLA 7 70 1.0000E+04 RPLB 7 131 1.0000E+05 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1.0000E+00 VE 6 14 2.1997E+00 RNLA 60 4 1.0000E+04 RNLB 141 4 1.0000E+05 * IP 7 4 4.7500E-03 DSUB 4 7 DM2 * MODELS .MODEL JM1 PJF (IS=2.9500E-11 BETA=1.7765E-03 VTO=-2.000000E+00) .MODEL JM2 PJF (IS=2.4500E-11 BETA=1.7765E-03 VTO=-1.999400E+00) .MODEL DM1 D (IS=1.0000E-15) .MODEL DM2 D (IS=8.0000E-16 BV=4.8000E+01) .MODEL DM3 D (IS=1.0000E-16) .MODEL DM4 D (IS=1.0000E-09) .ENDS * * * Linear Technology LT1178A op amp model (with calls for LT1179A) * Written: 06-20-1990 13:19:00 Type: Bipolar pnp input, internal comp. * Typical specs: * Vos=3.0E-05, Ib=3.0E-09, Ios=5.0E-11, GBP=6.0E+04Hz, Phase mar.= 60 deg, * SR(-)=2.5E-02V/us, SR(+)=2.4E-02V/us, Av= 117 dB, CMMR= 102 dB, * Vsat(+)=0.70V, Vsat(-)=0.00V, Isc=+/-10.0mA, Iq= 15uA. * (input common mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1178A/LT 3 2 7 4 6 * INPUT RC1 4 80 8.842E+04 RC2 4 90 8.842E+04 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 6.000E+02 RB2 3 103 6.000E+02 DCM1 105 102 DM2 DCM2 105 103 DM2 VCMC 105 4 4.000E-01 C1 80 90 8.660E-12 RE1 10 12 1.933E+04 RE2 11 12 1.933E+04 IEE 7 12 7.560E-07 RE 12 0 2.646E+08 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 8.984E-11 GA 8 0 80 90 1.131E-05 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 5.780E+02 * OUTPUT RO1 1 110 1.000E+02 RO2A 1 0 1.083E+03 RO2B 6 110 8.170E+02 EC 17 0 110 0 1 D1 1 17 DM1 D2 17 1 DM1 D3 110 13 DM2 D4 14 110 DM2 D5 6 110 DM2 D6 110 6 DM2 VC 7 13 1.480E+00 VE 14 4 7.806E-01 IP 7 4 1.424E-05 DSUB 4 7 DM2 * MODELS .MODEL QM1 PNP (IS=8.000E-16 BF=1.240E+02) .MODEL QM2 PNP (IS=8.009E-16 BF=1.261E+02) .MODEL DM1 D (IS=6.881E-16) .MODEL DM2 D (IS=8.000E-16) .ENDS * .SUBCKT LT1179A/LT 3 2 7 4 6 X_LT1179A 3 2 7 4 6 LT1178A/LT .ENDS * * * Linear Technology LT1220 op amp model * Written: 09-25-1990 13:27:33 Type: Bipolar NPN input, internal comp. * Typical specs: * Vos=5.0E-04, Ib=1.0E-07, Ios=1.0E-07, GBP=4.5E+07Hz, Phase mar.= 45 deg, * SR(-)=2.5E+02V/us, SR(+)=2.5E+02V/us, Av= 94.0dB, CMRR=114.0dB, * Vsat(+)=2.500V, Vsat(-)=2.000V, Isc=+25/-25mA, Rout= 25ohms, Iq=7.00mA. * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT LT1220/LT 3 2 7 4 6 * INPUT RC1 7 80 7.0736E+02 RC2 7 90 7.0736E+02 Q1 80 102 10 QM1 Q2 90 103 11 QM2 CIN 2 3 2.0000E-12 RB1 2 102 2.0000E+00 RB2 3 103 2.0000E+00 DDM1 102 104 DMZ DDM2 103 104 DMZ C1 80 90 2.5000E-12 RE1 10 12 +6.6591E+02 RE2 11 12 +6.6591E+02 IEE 12 4 1.2502E-03 * INTERMEDIATE GCM 0 8 12 0 2.8274E-09 GA 8 0 80 90 1.4137E-03 R2 8 0 1.0000E+05 C2 1 8 5.0000E-12 GB 1 0 8 0 1.4737E+01 RO2 1 0 2.4000E+01 * OUTPUT RSO 1 6 1.0000E+00 ECL 18 0 1 6 3.8378E+01 GCL 0 8 20 0 1.0000E+00 RCL 20 0 1.0000E+01 D1 18 19 DM1 VOD1 19 20 0.0000E+00 D2 20 21 DM1 VOD2 21 18 0.0000E+00 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1.0000E+00 VC 13 6 3.9909E+00 RPLA 7 70 1.0000E+01 RPLB 7 131 1.0000E+03 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1.0000E+00 VE 6 14 3.4909E+00 RNLA 60 4 1.0000E+01 RNLB 141 4 1.0000E+03 * IP 7 4 5.7498E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.0000E-16 BF=4.1639E+03) .MODEL QM2 NPN (IS=8.1562E-16 BF=1.2475E+04) .MODEL DM1 D (IS=1.0000E-20) .MODEL DM2 D (IS=8.0000E-16 BV=4.8000E+01) .MODEL DMZ D (IS=8.0000E-16 BV=5.2000E+0 RS=20) .MODEL DM3 D (IS=1.0000E-16) .MODEL DM4 D (IS=1.0000E-09) .ENDS * * * Linear Technology OP05A op amp model * Written: 08-23-1989 15:59:46 Type: Bipolar npn input, internal comp. * OP05A updated from original model on 06-20-1990 * Typical specs: * Vos=7.0E-05, Ib=7.0E-10, Ios=7.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=3.0E-01V/us, SR(-)=2.9E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq= 3000uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-05A/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 3.097E+03 RE2 11 12 3.097E+03 IEE 12 4 9.002E-06 RE 12 0 2.222E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 6.647E+02 * OUTPUT RO1 1 6 3.333E+01 RO2 1 0 6.667E+01 RC 17 0 1.393E-05 GC 0 17 6 0 7.179E+04 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.991E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=4.287E+03) .MODEL QM2 NPN (IS=8.022E-16 BF=1.286E+04) .MODEL DM1 D (IS=5.991E-12) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology OP05C op amp model * Written: 08-23-1989 15:59:46 Type: Bipolar npn input, internal comp. * OP05C updated from original model on 06-20-1990 * Typical specs: * Vos=3.0E-04, Ib=1.8E-09, Ios=1.8E-09, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=3.0E-01V/us, SR(-)=2.9E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq= 3000uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-05C/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 3.097E+03 RE2 11 12 3.097E+03 IEE 12 4 9.002E-06 RE 12 0 2.222E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 6.647E+02 * OUTPUT RO1 1 6 3.333E+01 RO2 1 0 6.667E+01 RC 17 0 1.393E-05 GC 0 17 6 0 7.179E+04 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.991E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=1.667E+03) .MODEL QM2 NPN (IS=8.094E-16 BF=5.001E+03) .MODEL DM1 D (IS=5.991E-12) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology OP05E op amp model * Written: 08-23-1989 15:59:46 Type: Bipolar npn input, internal comp. * OP05E updated from original model on 06-20-1990 * Typical specs: * Vos=2.0E-04, Ib=1.2E-09, Ios=1.2E-09, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=3.0E-01V/us, SR(-)=2.9E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq= 3000uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-05E/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 3.097E+03 RE2 11 12 3.097E+03 IEE 12 4 9.002E-06 RE 12 0 2.222E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 6.647E+02 * OUTPUT RO1 1 6 3.333E+01 RO2 1 0 6.667E+01 RC 17 0 1.393E-05 GC 0 17 6 0 7.179E+04 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.991E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.501E+03) .MODEL QM2 NPN (IS=8.062E-16 BF=7.502E+03) .MODEL DM1 D (IS=5.991E-12) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology OP07A op amp model * Written: 08-24-1989 12:35:59 Type: Bipolar npn input, internal comp. * OP07A updated from original model on 06-20-1990 * Typical specs: * Vos=1.0E-05, Ib=7.0E-10, Ios=3.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.5E-01V/us, SR(-)=2.4E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq=2500uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-07A/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 1.948E+03 RE2 11 12 1.948E+03 IEE 12 4 7.502E-06 RE 12 0 2.666E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.294E+03 * OUTPUT RO1 1 6 2.575E+01 RO2 1 0 3.425E+01 RC 17 0 6.634E-06 GC 0 17 6 0 1.507E+05 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.492E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=4.412E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=6.818E+03) .MODEL DM1 D (IS=1.486E-08) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology OP07C op amp model (with calls for OP07CS8) * Written: 08-24-1989 12:35:59 Type: Bipolar npn input, internal comp. * OP07C updated from original model on 06-20-1990 * Typical specs: * Vos=6.0E-05, Ib=1.8E-09, Ios=8.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.5E-01V/us, SR(-)=2.4E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq=2500uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-07C/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 1.948E+03 RE2 11 12 1.948E+03 IEE 12 4 7.502E-06 RE 12 0 2.666E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.294E+03 * OUTPUT RO1 1 6 2.575E+01 RO2 1 0 3.425E+01 RC 17 0 6.634E-06 GC 0 17 6 0 1.507E+05 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.492E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=1.705E+03) .MODEL QM2 NPN (IS=8.019E-16 BF=2.679E+03) .MODEL DM1 D (IS=1.486E-08) .MODEL DM2 D (IS=8.000E-16) .ENDS * .SUBCKT OP-07CS8/LT 3 2 7 4 6 X_OP07CS8 3 2 7 4 6 OP-07C/LT .ENDS * * * Linear Technology OP07E op amp model * Written: 08-24-1989 12:35:59 Type: Bipolar npn input, internal comp. * OP07E updated from original model on 06-20-1990 * Typical specs: * Vos=3.0E-05, Ib=1.2E-09, Ios=5.0E-10, GBP=6.0E+05Hz, Phase mar.= 70 deg, * SR(+)=2.5E-01V/us, SR(-)=2.4E-01V/us, Av= 114 dB, CMMR= 126 dB, * Vsat(+)=2.00V, Vsat(-)=2.00V, Isc=+/-25.0mA, Iq=2500uA * (input differential mode clamp active) * * Connections: + - V+V-O .SUBCKT OP-07E/LT 3 2 7 4 6 * INPUT RC1 7 80 8.842E+03 RC2 7 90 8.842E+03 Q1 80 102 10 QM1 Q2 90 103 11 QM2 RB1 2 102 5.000E+02 RB2 3 103 5.000E+02 DDM1 102 104 DM2 DDM3 104 103 DM2 DDM2 103 105 DM2 DDM4 105 102 DM2 C1 80 90 5.460E-12 RE1 10 12 1.948E+03 RE2 11 12 1.948E+03 IEE 12 4 7.502E-06 RE 12 0 2.666E+07 CE 12 0 1.579E-12 * INTERMEDIATE GCM 0 8 12 0 5.668E-11 GA 8 0 80 90 1.131E-04 R2 8 0 1.000E+05 C2 1 8 3.000E-11 GB 1 0 8 0 1.294E+03 * OUTPUT RO1 1 6 2.575E+01 RO2 1 0 3.425E+01 RC 17 0 6.634E-06 GC 0 17 6 0 1.507E+05 D1 1 17 DM1 D2 17 1 DM1 D3 6 13 DM2 D4 14 6 DM2 VC 7 13 2.803E+00 VE 14 4 2.803E+00 IP 7 4 2.492E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.586E+03) .MODEL QM2 NPN (IS=8.009E-16 BF=3.947E+03) .MODEL DM1 D (IS=1.486E-08) .MODEL DM2 D (IS=8.000E-16) .ENDS * * * Linear Technology OP27A op amp model (with calls for OP27E, OP227A, OP227E) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * OP27A updated from original model on 06-20-1990 * Typical specs: * Ref. OP-27 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT OP-27A/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 50 CXC1 91 90 500E-12 C2 8 98 4.000E-12 RXC2 8 98 4.00K CXC2 1 98 27.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.778E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=5.769E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * .SUBCKT OP-27E/LT 3 2 7 4 6 X_OP27E 3 2 7 4 6 OP-27A/LT .ENDS * .SUBCKT OP-227A/LT 3 2 7 4 6 X_OP227A 3 2 7 4 6 OP-27A/LT .ENDS * .SUBCKT OP-227E/LT 3 2 7 4 6 X_OP227E 3 2 7 4 6 OP-27A/LT .ENDS * * * Linear Technology OP27C op amp model (with calls for OP27G, OP227C, OP227G) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * OP27C updated from original model on 06-20-1990 * Typical specs: * Ref. OP-27 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT OP-27C/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 50 CXC1 91 90 500E-12 C2 8 98 4.000E-12 RXC2 8 98 4.00K CXC2 1 98 27.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.0000E-16 BF=2.0000E+03) .MODEL QM2 NPN (IS=8.0093E-16 BF=4.6667E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * .SUBCKT OP-27G/LT 3 2 7 4 6 X_OP27G 3 2 7 4 6 OP-27C/LT .ENDS * .SUBCKT OP-227C/LT 3 2 7 4 6 X_OP227C 3 2 7 4 6 OP-27C/LT .ENDS * .SUBCKT OP-227G/LT 3 2 7 4 6 X_OP227G 3 2 7 4 6 OP-27C/LT .ENDS * * * Linear Technology OP37A op amp model (with calls for OP37E, OP237A, OP237E) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * OP37A updated from original model on 06-20-1990 * Typical specs: * Ref. OP-37 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT OP-37A/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 200 CXC1 91 90 200E-12 C2 8 98 1.000E-12 RXC2 8 98 10.00K CXC2 1 98 5.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.000E-16 BF=2.778E+03) .MODEL QM2 NPN (IS=8.003E-16 BF=5.769E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * .SUBCKT OP-37E/LT 3 2 7 4 6 X_OP37E 3 2 7 4 6 OP-37A/LT .ENDS * .SUBCKT OP-237A/LT 3 2 7 4 6 X_OP237A 3 2 7 4 6 OP-37A/LT .ENDS * .SUBCKT OP-237E/LT 3 2 7 4 6 X_OP237E 3 2 7 4 6 OP-37A/LT .ENDS * * * Linear Technology OP37C op amp model (with calls for OP37G, OP237C, OP237G) * Written: 11-21-1989 Type: Bipolar npn input, internal comp. * OP37C updated from original model on 06-20-1990 * Typical specs: * Ref. OP-37 data sheet, LTC 1990 databook p2-345 * Comments: * Uses extended phase compensation; input differential mode clamp. * * Connections: + - V+V-O .SUBCKT OP-37C/LT 3 2 7 4 6 RC1 7 80 6.6315E+02 RC2 7 90 6.6315E+02 Q1 80 2 10 QM1 Q2 90 3 11 QM2 * C1 80 91 200E-12 RXC1 91 90 200 CXC1 91 90 200E-12 C2 8 98 1.000E-12 RXC2 8 98 10.00K CXC2 1 98 5.000E-12 * CIN 3 2 5E-12 DDM1 2 104 DM2 DDM3 104 3 DM2 DDM2 3 105 DM2 DDM4 105 2 DM2 RE1 10 12 -2.6233E+01 RE2 11 12 -2.6233E+01 IEE 12 4 7.5030E-05 RE 12 0 2.666E+06 CE 12 0 1.579E-12 GCM 0 8 12 0 7.558E-10 GA 8 0 80 90 1.5080E-03 R2 8 0 1.000E+05 GB 1 0 8 0 1.9176E+03 RO2 1 0 6.900E+01 * RS 1 6 1 ECL 18 0 1 6 2.828E+01 GCL 0 8 20 0 1 RCL 20 0 1E3 D1 18 20 DM1 D2 20 18 DM1 * D3A 131 70 DM3 D3B 13 131 DM3 GPL 0 8 70 7 1 VC 13 6 3.0909 RPLA 7 70 1E4 RPLB 7 131 1E5 D4A 60 141 DM3 D4B 141 14 DM3 GNL 0 8 60 4 1 VE 6 14 3.0909 RNLA 60 4 1E4 RNLB 141 4 1E5 * IP 7 4 2.625E-03 DSUB 4 7 DM2 * MODELS .MODEL QM1 NPN (IS=8.0000E-16 BF=2.0000E+03) .MODEL QM2 NPN (IS=8.0093E-16 BF=4.6667E+03) .MODEL DM1 D (IS=1.000E-19) .MODEL DM2 D (IS=8.000E-16) .MODEL DM3 D (IS=1.000E-20) .ENDS * .SUBCKT OP-37G/LT 3 2 7 4 6 X_OP37G 3 2 7 4 6 OP-37C/LT .ENDS * .SUBCKT OP-237C/LT 3 2 7 4 6 X_OP237C 3 2 7 4 6 OP-37C/LT .ENDS * .SUBCKT OP-237G/LT 3 2 7 4 6 X_OP237G 3 2 7 4 6 OP-37C/LT .ENDS * * end of library file